Safety Cover Tech Specs
Complete technical information including hardware components, installation process, measuring guidelines, and stock sizing.
Replacement Parts & Hardware
Short SS Spring
Stainless steel spring for close-mounted anchors
SS Spring
Standard stainless steel spring for perimeter mounting
SS Buckle
Stainless steel buckle for strap tensioning
Hex Key
Tool for anchor adjustment and installation
Concrete Anchor
Flush-mount brass anchor for concrete pool decks
Wood Anchor
Screw-type anchor for wood pool decks
Garden Stake
Ground stake for soft surface installations
Installation Rod
Tool for hooking springs to anchors during installation
Anchor Stake
Reinforced stake for lawn and garden areas
Spring Cover
Protective cap to cover anchors when the safety cover is removed
Installation Guide
Prepare & Position the Cover
Remove ladders and other obstructions from the pool deck. Measure the pool and the cover to make sure of a fit. For a 3 ft. grid cover, the cover size will be 2 to 3 ft. larger than the pool in both directions; for a 5 ft. grid cover, it is oversized 1½ to 2 ft. Lay the cover over the pool and adjust for equal overlap to all corners of the pool. Overlap will be 11 to 14" for 5 ft. grid, 13 to 18" for 3 ft. grid. Pull cover tightly to remove packing wrinkles. Install buckles, springs and spring covers onto the straps at the 8 corner strap locations. Adjust to equal lengths.
Install Corner Anchors
Install anchors at the corners of the cover first. To determine the anchor points, measure 18" from the cover edge at a right angle to the cover, over the straps, and mark. Using a ¾" concrete bit in a rotary hammer drill, drill 2 to 3" deep holes and clean out the concrete dust. Hammer the brass anchors into place using the tamping tool provided, and insert the anchor screws using the hex key provided.
Attach Corner Springs
Attach the corner springs to the anchors using the installation rod provided. Use the rod by keeping the notched area towards the pool and pulling the handle away from the pool until the heel is free from the anchor. Ensure the overlap is equal on sides and ends — adjustments can be made by adjusting strap lengths at the buckle. Springs should be 10 to 20% compressed for proper tension.
Install Remaining Anchors & Springs
Install the remaining buckles, springs, and spring covers on all remaining straps. Install brass anchors as before by measuring back 18" from the cover edge in a straight line with each strap. Place springs on the anchors with the rod, starting at the centre of each side and working alternately from side to side.
Wood Anchor Installation
Using a 1½" wood drill, create a ⅛" deep recess hole. At the centre of this hole, drill a ¾" x 2" deep hole (or through the wood). Drop in your anchor and fasten with the 4 wood screws provided.
Form Fit Installation
Lay out the cover ensuring the overlap is equal around the perimeter. Starting at the centre of the sides, mark and drill for the brass anchors (4 total — 2 on each side). Secure the springs, alternating from side to side. Mark and drill the remaining holes and continue around the pool, again alternating from side to side.
Removing Your PSP Safety Cover
Insert the installation rod between the spring and the anchor. Tip the rod towards the cover to slip the spring off the anchor. Carefully pull the cover off the pool. Clean it, fold it, and put it back in the mesh bag provided. Using your hex key, sink your anchors to deck level for summer.
On completion of the installation, all springs should have equal tension and your cover should be straight and wrinkle free.
A-B Measuring Guide
For custom-shaped pools, we use the A-B measuring method to create a precise template of your pool's perimeter. If your pool is a standard shape, simply provide the width and length measurements.
Draw a sketch of the pool shape on the grid provided in the measuring sheet.
To represent the A–B line, mark 2 points on the deck about 3 feet away from the pool. Note that A is always on the left of B as you face the pool, and the pool is in front of your A–B line. The A–B distance should be about ⅔ of the total length of the pool. Make sure the A–B line does not cross the pool.
Measure the A–B length and enter it in the space provided on the sheet.
Use chalk to mark points clockwise around the entire inside edge of the pool at about 3-foot intervals. The first point should be directly across from the center of the A–B line. All corners including steps should be marked, and inside curves should be marked at 1-foot intervals.
Any obstructions (slides, legs, ladders, rock waterfalls — all non-removable obstructions) within 18 inches of the water edge should be marked.
Using a measuring tape, measure the distance from point A to all the points on the pool starting from #1 and record it in the A column. Likewise, measure the distance from B to all points and record it.
Contact us for a printable measuring sheet
705-797-1320 | Fax: 705-797-1380
Important: Measure all radius corners and make sure all radii are equal. A slight difference in each radius will affect the fit of your cover.
Stock Covers
Standard shapes and sizes ready to deliver within 24 hours. All covers are standard mesh with 5' x 5' grid. Covers include all hardware and storage bag. Available in Green and Taupe.
| # | Pool Size | Cover Size | Hardware Pcs |
|---|---|---|---|
| 1 | 12x24 | 14x26 | 22 |
| 2 | 14x28 | 16x30 | 22 |
| 3 | 16x32 | 18x34 | 26 |
| 4 | 16x34 | 18x36 | 26 |
| 5 | 16x36 | 16x40 | 26 |
| 6 | 16x40 | 18x42 | 26 |
| 7 | 18x36 | 20x38 | 28 |
| 8 | 18x40 | 20x42 | 28 |
| 9 | 20x40 | 22x42 | 30 |
Warranty
PSP Fabricating Inc. warrants the purchaser of our safety cover that any defects in material or workmanship will be repaired or replaced, at the company's discretion, free of charge within five (5) years of the purchase date.
Warranty Exclusions
- •Water level drops below 18" of the deck during the snow season
- •The PSP Safety Cover is used on any pool for which it was not designed
- •Cover is subject to obvious misuse, improper installation, or damage caused by falling sharp objects (e.g. tree limbs)
- •PSP Fabricating does not cover service, installation, or freight under this warranty
In order to complete your warranty registration form, please have your sales receipt ready.